AUTOFLAME燃烧器带程序控制器MMM8002,
AUTOFLAME伺服电机MM10004
AUTOFLAME电动执行机构MM10005
AUTOFLAME火焰探测器MM60004/HSU
AUTOFLAME燃烧控制器MMM8002-MIN50/60H
elektrogas安全电磁阀 VMR（快开快闭型）VMR3-2 DN25
elektrogas伊莱克斯紧急切断阀EVRM-NA/6NA，EVRM-NC/6NC
elektrogas安全电磁阀VMR（快开快闭型）VMR3-2 DN25
elektrogas伊莱克斯紧急切断阀EVRM-NA/6NA，EVRM-NC/6NC
Weishaupt威索伺服电机1055/23,L/A-LFST，G-GAS,
Weishaupt威索风门执行器1055/23，1055/80
Weishaupt威索控制单元显示操作面板WMF20，AM20.02
Weishaupt威索控制器LMV37.410A1WH，AZL52.00B1WH
W-MF10 LM082.120A2WH，LMV27.210A2WHW-FM50
Weishaupt威索温控器 KS40-108-9090E-D51
Weishaupt威索燃烧器专用伺服电机1055/23,L/A-LFST,燃气伺服G-GAS,
Weishaup威索燃气阀W-WF-S512 C01 S22，W-MF-SE 507 C01 S22
W-MF 507C 032/P
Weishaupt威索WDK3/01 S2
Weishaup威索伺服马达STA13 B0.36/8 2N36L
9 100mA 仅用于驱动继电器/灯 – 切换至中性
120V Unit:
120V设备
Outputs Terminal 57 250mA Must be connected through contactor Max Load 5A
输出 端口 57 250mA 必须通过接触器连接，*大荷载5A
58 250mA Must be connected through contactor
58 250mA 必须通过接触器连接
59 2A 0.6 power factor
59 2A 0.6 功率因数
60 2A 0.6 power factor
60 2A 0.6 功率因数
61 2A 0.6 power factor
61 2A 0.6 功率因数
62 2A 0.6 power factor
62 2A 0.6 功率因数
63 2A 0.6 power factor
63 2A 0.6 功率因数
78 100mA To drive relay only – switched neutral
78 100mA 仅用于驱动继电器 – 切换至中性
79 100mA To drive relay/lamp only – switched neutral
79 100mA 仅用于驱动继电器/灯 – 切换至中性
Note:
注意：
1. The high and low voltage connections are not safe to touch. Protection against electric shock is
provided by correct installation. CAUTION – ELECTRIC SHOCK HAZARD.
用手触摸高压和低压连接是危险行为。正确安装电气设备可以防止触电事故。警告：触电危
险。
2. Control voltage cabling should be maximum 10m, screened (if not screened then less than 1m,
however servomotors can be unscreened up to 10m)
控制电压电缆的*大长度应为10m，经屏蔽（若未屏蔽应短至1米）；伺服马达的未屏蔽电缆
*大长度可为10m。
3. Any cabling over 10m must have additional surge protection.
所有超过10m的电缆必须配备电涌保护。
4. Low voltage cables should be screened cable as specified in section 1.3.3.
低压电缆应符合章节1.3.3规定的经屏蔽电缆。
5. The burner ‘High Limit Stat’ must be a manual reset type.
燃烧器的“上限启停控制器”必须为手动复位型。
Note: There is a lid (back plate) fitted onto the back of the Mini Mk8 M.M. with a Warning label to
prevent any unauthorised fuse replacements.
注意：在MK8微型控制模块背部装有一个盖板。盖板上的标识明确指出更换保险丝操作前必需
获得授权
扫一扫，手机浏览
